Talk to an ergo expert: (888) 420-3200 or Email Us
The CONNECT-2 is a robust, highly adjustable dual monitor stand capable of handling two monitors each weighing up to 30 pounds and measuring 28.5 inches in width. The horizontal beam holding the monitors can be mounted at any height along the sturdy central column. The monitors can be placed anywhere along the beam. The two premium VESA monitor mount mechanisms provide instant landscape/portrait orientation adjustment, as well as substantial swivel and tilt capability. The wire management provides simple and effective cable routing, reducing clutter. Clamp or thru-desk mount options are available.
If you only need two monitors to start with, but think you may later expand to three, four, or even eight screens, the CONNECT-2 is likely the perfect fit for you. The CONNECT system is based on a modular design, allowing you to gradually expand your set-up by adding additional monitors while reusing virtually all of the original components.
Motorized Height Adjustment
The CONNECT-2 dual monitor stand has an optional motorized column providing 10 inches of vertical adjustment at the touch of a button. The mechanism lifts and lowers all monitors simultaneously. This feature is especially useful in multi-user environments.
|Connect-2 Shipping Weights and Dimensions|
|Static Column||21 lb, 40"x14"x6"|
|Motorized Column||box1: 15 lb, 27"x9"x4", box2: 14 lb, 32"x15"x4"|
|Clamp Mount||adds 7 lb to box1|
Monitors are placed in a side-by-side configuration along a 30 inch beam with two fully articulating monitor mounts called tilter mechanisms, also known as tilter heads.
Static columns are used to mount the horizontal beams. Each beam can be placed anywhere along the column during installation. The single static column is 17 inches in height.
The motorized column is an optional feature. It enables up to 10 inches of simultaneous height adjustment for both monitors when the button located at the base is pressed.
In this configuration, the CONNECT-2 can accommodate monitors that each measure up to 28.5 inches wide in landscape orientation.
The horizontal bar of the highly adjustable CONNECT-2 measures 30 inches across. If both monitors are of equal size, the maximum width of each monitor can be approximately 28.5 inches when they are in a flat configuration.
When the two monitors for the CONNECT-2 are rotated inward, the maximum width can be as little as 25 up to 27.5 depending on how thick the monitors are. The maximum allowable width is slightly increased when they are displayed flat.
The side view of the single tier configuration with the clamp mount assembly and the tilter mechanism show that the depth of the stand before the monitor is placed is 8.5 inches.
The 100 x 200 mm VESA adaptor is compatible with certain larger monitors. It is used to attach the monitor to an Ergomart tilter head, present in all SAA, SA, and LS arms and mounts. If your monitor has a recessed VESA attachment point, you may also need an Ergomart VESA spacer kit, available below in the accessories tab.
This large VESA bracket is intended for mounting a monitor or TV with a 200x200 mm, 100x200 mm, or 120x180 mm hole pattern. The central hole patterns are 50x50 mm, 75x75 mm, and 100x100 mm, enabling this bracket to attach to the mounting location (e.g. an Ergomart Tilter Head) using a VESA 75/100 adaptor.
The large 200x400 mm VESA adaptor plate supports 50 mm, 75 mm, 100 mm and 200 mm square patterns, as well as 100x200 mm, 120x180 mm, 200x300 mm and 200x400 mm rectangular patterns. In some cases an additional 75 or 100 mm VESA adaptor is needed to interface the 200 x 400 mm VESA plate to the mounting location.
The extra large MSU4X6 VESA adaptor bracket attaches to a wide range of VESA patterns from 100x300 mm up to 400x600 mm. The hole patterns on the central plate allow it to be mounted to tilter heads or wall mounts, often using an additional smaller VESA plate (e.g., 75 mm, 90 mm, 100 mm, 200 mm or 100x200 mm) in between.
This VESA 1/4-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/4" or less to be attached to an Ergomart VESA plate.
This VESA 1/2-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/2" or less to be attached to an Ergomart VESA plate.