Each base is nominally .25" thick.
The PM192-EZ1 Lobby Display Large Monitor Pole Stand is an exceptional mounting solution for the largest LCD, LED and Plasma monitors and televisions. The display mount is well-suited for use in medical facilities, retail environments, or anywhere a free-standing display with a minimal footprint would be useful. Its heavy-duty, sturdy construction will last even in the toughest environments.
The PM192-EZ1 features the heavy-duty PM80 monitor mount capable of handling devices from 35 to 80 pounds and providing substantial tilt capabilities: 45° upwards and up to 44° down, depending on monitor height, to allow for adjustment to the best viewing angle. Tilt resistance can be modified when needed. This mount is compatible with 75 x 75 mm, 100 x 100 mm and 100 x 200 mm VESA hole patterns. Larger, optional VESA adapters available in the Accessories section of this page support devices with hole patterns ranging from 200 x 200 mm to 200 x 400 mm. An extra-large VESA mount is also available the Accessories tab and is compatible with VESA sizes to 100 x 300 mm up to 400 x 600 mm. For detailed information on the VESA mounting interface, visit our VESA reference page. Please note that the PM80 does not have side-to-side rotation capabilities.
The monitor mount is attached to a sturdy PM192 pole and base. There are 5 pole length options: 4', 5', 6', 7' and 8'. The largest two sizes may require additional lead time, please contact Ergomart regarding shipping times for the 7' and 8' lengths. Each pole features a cable access port at the top and bottom, allowing for wires to be fed through the length of the pole to minimize clutter and safety hazards from loose cables.
The base of the stand has three options: flange, center and offset. The PM192 Flange Base has the smallest footprint and is designed to be bolted to the floor. This is the ideal option for displays that will remain permanent fixtures as it provides the most stability regardless of the mounted device. The PM192 Center Base is a wide 30-inch base where the pole is positioned directly in the middle. When unloaded, the stand can be re-positioned. The third base is the PM192 Offset Base. This is the best repositionable option for devices that are on the heavier side of the supported weight range. Please contact Ergomart if you have any questions regarding stability or safety of the device based on your mounting needs.
An optional base cover is available for use with any of the bases. The cover fully encloses the base of the PM192 Flange Base and covers the flange component on the PM192 Center and Offset Bases. Constructed of temperature, chemical and impact-resistant ABS, the cover is built to handle the toughest environments while adding an attractive look to the stand that protects and guides cables as they exit the bottom of the pole.
The PM192-EZ1 Lobby Display Large Monitor Pole Stand is part of an entire family of modular mounts that can be assembled to meet almost any need. It can be augmented by adding a CPU bracket or any number of "PM" monitor and keyboard mounts. The PM192 pole accepts three mount kits, namely MKIT-E (single), MKIT-J (double), and MKIT-Y (pole top). Each of these kits is compatible with all SERIES-118 arms and mounting devices. A number of VESA and other monitor accessories are also available to address additional usage scenarios. Our team at Ergomart is always ready to help you design a system that works for your requirements.
|Shipping Weight||Monitor Mount: 13 pounds | 23 pounds (MSU4x6 VESA option)
Base: Center/Offset: 65 pounds | Flange: 10 pounds
Pole: 14 to 30 pounds, depending on length
Base Cover: 1.5 pounds
|Shipping Dimensions||Monitor Mount: 17" x 14" x 16" | 27" x 16" x 9" (MSU4x6 VESA option)
Base: Center/Offset: 30" x 30" x 6" | Flange: 13" x 13" x 6"
Pole: 49" x 5" x 5" to 100" x 5" x 5", ships in separate box
Base Cover: 13" x 13" x 6"
|Warranty||5 year limited|
The monitor mount has a dual tilter head and mount to manage heavier and larger monitors and TVs.
The monitor mount has a dual tilter head and mount to manage heavier or larger monitors and TVs.
Top view of the monitor mount showing various measurements including the 8" length of the arm and tilter mechanism combination.
VESA option 100x200mm, side view with monitor tilter head and mount.
VESA option 100x200mm, front view with monitor tilter head and mount.
VESA option 200x200mm, side view with monitor tilter head and mount.
VESA option 200x200mm, front view with monitor tilter head and mount. This VESA size can be selected from the accessories tab.
VESA option 200x400mm, side view with monitor tilter head and mount. This VESA size can be selected from the accessories tab.
VESA option 200x400mm, front view with monitor tilter head and mount. This VESA size can be selected in the accessories tab.
VESA option MSU4X6, side view with monitor tilter head and mount. This VESA size can be selected from the accessories tab.
The MSU 400x600 VESA plate is used to accommodate very large monitors and TVs. It is shown here in its widest (black) and narrowest (gray) configurations. This VESA plate can be selected from the accessories tab.
|SAMPLE MONITOR HEIGHTS AND ESTIMATED RESULTING TILT RANGES|
|The pole will naturally create an impediment to the tilt range based on the height of the monitor. The below table predicts the approximate tilt range of various LCD monitors and TV screens with a VESA hole pattern vertically centered.|
The image above shows the various pole lengths available. All poles come standard with the access ports at top and bottom. The right-most images show the top of the pole. The top image includes the cable access port. A minor pole seam is visible through the opening and is indicated by the two vertical lines. The outside dimension of the pole is 1.92 inches as shown in the lower image.
The image on the left illustrates the proportions of the flange base with a 72-inch pole. The middle and right images show the base on its own from the side and top.
The image on the left illustrates the proportions of the offset base with a 72-inch pole. The middle and right images show the base on its own from the side and top.
The image on the left illustrates the proportions of the center base with a 72-inch pole. The middle and right images show the base on its own from the side and top.
The above drawing depicts an isometric view of the base cover designed to cover the entirety of the flange that accepts the 1.92" diameter pole on all PM192 floor stands.
This side view of the base cover shows all of its critical dimensions. The total height is 5.53", the diameter is 12.63". The rectangular wire access hole is 1" x 1.45". The wall thickness is 0.25" and the hole at the top that accepts the pole is 1.96" in diameter.
This large VESA bracket is intended for mounting a monitor or TV with a 200x200 mm, 100x200 mm, or 120x180 mm hole pattern. The central hole patterns are 50x50 mm, 75x75 mm, and 100x100 mm, enabling this bracket to attach to the mounting location (e.g. an Ergomart Tilter Head) using a VESA 75/100 adaptor.
The large 200x400 mm VESA adaptor plate supports 50 mm, 75 mm, 100 mm and 200 mm square patterns, as well as 100x200 mm, 120x180 mm, 200x300 mm and 200x400 mm rectangular patterns. In some cases an additional 75 or 100 mm VESA adaptor is needed to interface the 200 x 400 mm VESA plate to the mounting location.
The extra large MSU4X6 VESA adaptor bracket attaches to a wide range of VESA patterns from 100x300 mm up to 400x600 mm. The hole patterns on the central plate allow it to be mounted to tilter heads or wall mounts, often using an additional smaller VESA plate (e.g., 75 mm, 90 mm, 100 mm, 200 mm or 100x200 mm) in between.
This VESA 1/4-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/4" or less to be attached to an Ergomart VESA plate.
This VESA 1/2-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/2" or less to be attached to an Ergomart VESA plate.
Each base is nominally .25" thick.
Yes, the flange comes attached to the base plate. The allen wrench needed to secure the pole in place once installed is included.
The PM192 Offset Base is designed to handle payloads with a forward cantilevered orientation. Vibration or wobble can be a subjective issue or experience. Consult an Ergomart product specialist before purchasing your initial order to determine and discuss the suitability of this product for your application.
No, the PM192 Flange Base is not intended to act as a freestanding base. It must be bolted to the floor or surface. Please select the PM192 Center or Offset Base for a freestanding base.
The holes on the flange are through holes for fasteners up to 3/8" in diameter. However, we don't know the specifics of each installation, and for that reason customers are responsible for determining the appropriate fastener to use for their given installations. If you have any questions regarding the appropriate fastener for your application work with an installation professional, consult a civil or mechanical engineer or call Ergomart product experts with your questions.
The flange can be mounted to wood and concrete. For more guidance on the appropriateness of this product for your specific application(s) please contact customer service with the details of your project.
Ceiling mounted versions of the PM192 Flange Base are available using a modified pole and with certain weight limitations. Contact an Ergomart representative with your specifications and we will provide part numbers and a quotation suitable to your needs.
The PM80 monitor mount does not move side to side, but does offer up and down tilting.
We may be able to provide a solution based on the weight of your monitor. Contact us for a quotation that increases the reach by 5 inches.