Talk to an ergo expert: (888) 420-3200 or Email Us
With its substantial range of vertical motion of almost 18 inches and generous tilt, this keyboard tray and arm combo is ideal for many work environments. The TRP2718D frees up workspace and offers sit-to-stand adjustability. It accommodates two displays up to 8 pounds each. Both the arm and the tray can rotate 360 degrees and the monitors and tray can be tilted at different angles. Great wire management allows for cabling to be routed conveniently through the arm just above the mount. The arm can reach out up to 27 inches but folds away to a mere 7 inches from the wall when not in use. The brake and vertical travel limiter option allows for securing of the vertical position and limits on reach so as to not interfere with other workspace equipment.
This workstation is also available as the TRP2718S Monitor and Keyboard Arm that mounts a single monitor up to 18 pounds.
|Shipping Weight||35 pounds|
|Shipping Dimensions||31" x 19" x 9"|
|Warranty||5 year limited|
Professional installation is always recommended for all wall-mounted Ergomart products. Improper installation may result in injury or damage. Consult Ergomart technical support regarding any mounting concerns or questions.
This image depicts the arm wall mounted and raised to its highest position. The lifting arm intersects with the keyboard bracket via an HD tilter mechanism. There are three locations that allow the keyboard bracket to be higher or lower in relation to the arm. There are three increments that are 1.9 inches apart. The dual bracket will place the monitor centers at 13.25 or 11.25 inches above the tray depending on the requirement.
This image depicts the arm wall mounted and raised to its highest position. The lifting arm intersects with the keyboard bracket via a tilterhead mechanism. There are three locations that allow the keyboard bracket to be higher or lower in relation to the arm. These three increments are 1.9 inches apart. The dual bracket will place the monitor centers at 13.25 or 11.25 inches above the tray depending on the requirement.
Velcro can be used to attach a keyboard to the tray, thereby allowing the user to stow the tray vertically, freeing up space and reducing clutter.
The TRP2718D comes with a 31" wide bracket for dual monitor mounting.
The TRP2718D comes with the ADJ1430 Dual Monitor Bracket allowing both vertical and hoizontal adjustment of the monitors.
The TRP2718D has the option of 3 different sizes of VESA plates based on the required hole pattern of the specific VESA pattern of the monitors
The horizontal line illustrates the plane where the face of the arm meets the top of the pole mount (mounting plane). This is instructive for the installation process and determining the vertical position of the monitor and tray heights. The arm may be lowered just using hand pressure to a position as illustrated. The tray in this configuration is able to move over 11 inches below the mounting plane.
In this illustration, the TRP2718D is in its most extended configuration, reaching a lateral length of 41.25 inches. A horizon line created by the junction of the arm and wall mount will be 1 inch above the keyboard tray surface.
In its highest elevation the bottom of the keyboard tray will be over 7 inches above the mounting plane.
This configuration illustrates the desk-mounted TRP2718D at its lowest position. The bottom horizontal line illustrates the surface height for a clamp, grommet or through desk configuration. In this set-up the keyboard tray will rest directly on the surface of the desk or table.
In the horizontal configuration the TRP2718D reaches almost 42 inches in lateral length, with the bottom of the keyboard tray a comfortable 2.5 inches above the work surface.
This monitor arm keyboard arm configuration illustrates the tilt mechanism attached to the top of the back bar and is only advised for lighter payloads or in certain situations where the ergonomic geometries are enhanced for ease of use. Note that the mechanism can be located 6.7, 8.6 or 10.5 inches above the tray. The bottom horizontal line illustrates the surface height for a clamp, grommet or through desk configuration. The arm will have 7.9 inches of vertical travel in this configuration as the tray will be impeded at the point it contacts the worksurface.
These extensions are almost always used when the arm is attached to a large horizontal surface. In a desk-mounted configuration with a 5 inch extension the work surface will limit the full vertical range of the TRP2718D in the down position.
With an 8 inch vertical extension the bottom of the keyboard tray will be able to float 1.75 inches above the work surface.
The 12 inch Vertical Extension allows for a large range of movement with the bottom of the keyboard tray a generous 5.75 inches above the work surface.
The TRP2718D is shown desk-mounted with the optional 5 inch extension placed in the highest position. Also note the maximum height of the backbar. In this illustration the bar is attached to its tilter at the lowest possible location, the backbar has the ability to be placed 3.8 inches higher in 1.9 inch increments.
The TRP2718D is shown desk-mounted with the optional 8 inch extension placed in the highest position.
The TRP2718D is shown desk-mounted with the optional 12 inch extension floated to its highest position.
This VESA 1/4-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/4" or less to be attached to an Ergomart VESA plate.
This VESA 1/2-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/2" or less to be attached to an Ergomart VESA plate.