The TRP2718S Premium LCD Arm FlexTray is useful in space sensitive environments. It is an excellent choice for wall mounting for occasional data entry in both standing and sitting positions. This LCD Arm FlexTray assembly is used extensively in medical, dental, manufacturing and industrial work environments. The TRP2718S accommodates flat panel displays up to 20 pounds. The arm and tray rotate an amazing 360 degrees at three pivot joints while cables are routed through the arm. Both monitor and keyboard tray can be tilted at different angles. If you require greater reach or a combo that handles greater payloads, contact Ergomart at 888 420 3200. One more great feature: the arm can be folded so that when not in use it only protrudes about 7 inches from the wall. The brake and vertical travel limiter option allows the user to secure the vertical position with a twist of a knob, while limiters may be set to ensure arm does not go too high or low in a workspace and collide with important equipment or obstacles.
Need two monitors? This mount as also available as the TRP2718D Dual Monitor Arm with Keyboard Tray, providing side-by-side mounting of two monitors.
|Shipping Weight||35 pounds|
|Shipping Dimensions||31" x 19" x 9"|
|Warranty||5 year limited|
Professional installation is always recommended for all wall-mounted Ergomart products. Improper installation may result in injury or damage. Consult Ergomart technical support regarding any mounting concerns or questions.
This image depicts the arm wall mounted and in its highest position. VESA monitor placement can be in either the lowest (7.4) or the highest (11.2) position or halfway inbetween.
There are three attachment positions for the tilter head to the LCD Keyboard Tray Arm. They move the relationship of the arm to the backbar that hold both the tray and the monitor. Most installations work best with the tilter attached to the lowest point on the backbar. This is the preferred position because it reduces the stress on the tilter head component. That position is indicated in the image to the left with the fully opaque lines. Again, this same attachment position is also typically advisable when attaching the arm to a work surface as it will allow for the most vertical travel before the keyboard tray stops when it rests on the surface.
Velcro can be used to attach a keyboard to the tray, thereby allowing the user to stow the tray vertically, freeing up space and reducing clutter.
The horizontal line illustrates the plane where the face of the arm meets the top of the pole mount (mounting plane). This is instructive for the installation process and determining the vertical position of the monitor and tray heights. The arm may be lowered just using hand pressure to a position as illustrated. The tray in this configuration is able to move over 11 inches below the mounting plane.
In this illustration, the TRP2718S is in its most extended configuration, reaching a lateral length of 41.25 inches. A horizon line created by the junction of the arm and wall mount will be 1 inch above the keyboard tray surface.
In its highest elevation the bottom of the keyboard tray will be over 7 inches above the mounting plane.
This configuration illustrates the desk-mounted TRP2718S at its lowest position. The bottom horizontal line illustrates the surface height for a clamp, grommet or through desk configuration. In this set-up the keyboard tray will rest directly on the surface of the desk or table.
In the horizontal configuration the TRP2718s reaches almost 42 inches in lateral length, with the bottom of the keyboard tray a comfortable 2.5 inches above the work surface.
The arm will have over 11 inches of vertical travel when limited by the surface, with the top of the monitor bracket reaching 28 inches.
These extensions are almost always used when the arm is attached to a large horizontal surface. In a desk-mounted configuration with a 5 inch extension the work surface will limit the full vertical range of the TRP2718S in the down position.
With an 8 inch vertical extension the bottom of the keyboard tray will be able to float 1.75 inches above the work surface.
The 12 inch Vertical Extension allows for a large range of movement with the bottom of the keyboard tray a generous 5.75 inches above the work surface.
The TRP2718S is shown desk-mounted with the optional 5 inch extension placed in the highest position. Also note the maximum height of the backbar. In this illustration the bar is attached to its tilter at the lowest possible location, the backbar has the ability to be placed 3.8 inches higher in 1.9 inch increments.
The TRP2718S is shown desk-mounted with the optional 8 inch extension placed in the highest position.
The TRP2718S is shown desk-mounted with the optional 12 inch extension floated to its highest position.
This VESA 1/4-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/4" or less to be attached to an Ergomart VESA plate.
This VESA 1/2-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/2" or less to be attached to an Ergomart VESA plate.