Typically, no, our mounts are designed specifically for Ergomart products. Contact Ergomart to determine if you would like assistance.
Talk to an ergo expert: (888) 420-3200 or Email Us
- GSA
- Help & About
-
- Contact Us
MONDAY - THURSDAY: 8:00 AM - 6:00 PM CST FRIDAY: 8:00 AM - 5:30 PM CST
Phone - Toll Free: 888-420 3200 Phone - Outside US: +1 (214) 742-6066 Se Habla Español: Extensión 231 Contact us for secure fax ordering
- Contact Us
-
- Custom Solutions
SKU
MKIT-M
Mounting Kit M allows users to mount a stationary arm or equipment holder to a roller track.
The mount's back plate is slid into either of the roller track for installation.
Four set screws fix the mount at any point along the track. Loosening the screws allows for repositioning of the MKIT-M.
When purchased with shaft collars, the mount can be used to hold an Ergomart LS type pole allowing for placement of peripherals above and below the mount along the pole.
Mounting Kit M is an economical mounting solution for roller track users who do not need on demand or instantaneous lateral repositioning capability.
Compatible arm models: SAA7000, SAA2010, SAA2045, SAA179, SAA2718, SAA2415, SAA4228, SAA4229, CMD2018, CMD2415, CMT2415, most TRS series monitor keyboard tray arms, arm based tablet and ipad holders, VE vertical extensions and EQP3418 equipment arms.
MOUNT KIT M
PERSPECTIVE VIEW
MOUNT KIT M
FRONT VIEW
MOUNT KIT M
SIDE VIEW
MOUNT KIT M
TOP VIEW
200x200mm Flat VESA Plate with Hardware
This large VESA bracket is intended for mounting a monitor or TV with a 200x200 mm, 100x200 mm, or 120x180 mm hole pattern. The central hole patterns are 50x50 mm, 75x75 mm, and 100x100 mm, enabling this bracket to attach to the mounting location (e.g. an Ergomart Tilter Head) using a VESA 75/100 adaptor.
QTY:
$20.00
200x400mm Flat VESA Plate with Hardware
The large 200x400 mm VESA adaptor plate supports 50 mm, 75 mm, 100 mm and 200 mm square patterns, as well as 100x200 mm, 120x180 mm, 200x300 mm and 200x400 mm rectangular patterns. In some cases an additional 75 or 100 mm VESA adaptor is needed to interface the 200 x 400 mm VESA plate to the mounting location.
QTY:
$25.00
VESA 1/4-inch Spacer Kit
This VESA 1/4-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/4" or less to be attached to an Ergomart VESA plate.
QTY:
$2.00
VESA 1/2-inch Spacer Kit
This VESA 1/2-Inch Spacer Kit allows monitors with VESA hole locations that are recessed by 1/2" or less to be attached to an Ergomart VESA plate.
QTY:
$3.00
Overall Rating
Leave a Review
Leave a Review
-
Will your mount kits work with 3rd party arms?
-
Is there a way that I remove my arm and just put the tilter head in to the mount kit?
No and Yes. Since the tilter head pin is a smaller size than the arm pin, you would not be able to do that without installing an adapter bushing into the mount. Contact Ergomart if you wish to purchase the adapter.
-
What if we need to move the monitors over to make room for another, could they slide?
The set screws on the mounts are easily loosened to slide the mount over. With very light loads it is possible to leave the arm and the payload on the MKIT-M and slide. Bigger payloads and long arms with extensions will require removal before shifting the mount.
-
Are these hard to reposition once they're on the track?
The MKIT-M by itself is easy to move when the set screws are slightly loosened. And lighter loads it is possible to leave the arm and the payload on the MKIT-M and move laterally to the desired spot. Bigger payloads and long arms with extensions will require removal before shifting the mount.
-
Can I readjust the position of this mount on the track with a load on it?
In some cases it is reasonably easy. Loosen all four set screws about two rotations and very slightly raise the arm and payload upward to shift. Be careful not to pull the pin out of the mount. With heavier payloads (over ten pounds) and long reach solutions, remove the payload first.
More Products You Might Find Interesting
